Automatic cutting data input system based on CIP3/4.
CIP4 data is received from the world standard JDF file, automatically calculated and passed to the cutting machine as cutting data.
*Since JDF/CIP4 PPF data cannot be used directly as cutting data, installation of N-Cutmaster can automatically converts to cutting data.
● Optional setting for D7 and D8 series.
● The setting work of the operator can be greatly shortened, and the operating efficiency of the cutting machine can be improved.
●As it is possible to input in advance from the office, reliable production control and planned production are possible.
●Detection accuracy is 0.2mm. The operation stops even with a small gap.
●Cutting mistake when paper without properly hitting the back gauge condition can be prevented.
●Cutting mistake when the work is separated from the back gauge condition can be prevented.
●Cutting mistake when the paper is bending condition can be prevented.
● A powerful ally when cutting products with strict right-angle accuracy in fully automatic mode.
Display the total number of cut sheets with one touch.
After calculating the thickness of one sheet, the number of sheets is automatically calculated with one pedal.
You can save time and effort to calculate with a calculator.
● Count the number of sheets at the clamp height. The error is 1000 sheets, ±2 to 3 sheets.
●Measured values can be printed and saved. It can also be used as a voucher for number of sheets and as an operation record, which helps build trust with customers.
●The problem of insufficient number of sheets is eliminated when cutting.
Productivity improvement application number Utility model application 2004-6530
Filing date November 8, 2004
Registration number Registered utility model No. 3108619
Registration date February 16, 2005
Utility model holder Nagai Kikai Seisakusho Co., Ltd.
Creator Kunio Tanaka
Name of device Automatic counting system in cutting machine
Safety Support Device : CLAMP SENSOR
Prevention of finger injury during pedal clamp operation
During cutting operation, the cutting position of the work is adjusted by the operator by pedaling the foot clamp.At that time, the operator`hand is put under the clamp incautiously and can have an injury unfortunately.
Until now, safety measures have been taken to prevent accidents, such as attaching a cover to the pedal or using a safety auxiliary device such as a soft clamp to reduce the pedal pressure of the clamp.
By installing "Soft Clamp Function", even if the finger is put by clamp accidentally, the pedal clamp pressure is restricted to 20kg so the finger did not get injured as expected.
Nevertheless ...the operator may feel insecure.... "I was surprised when I operated the clamp even though I had my hands in it." "I got injured by pinching my finger." ・ ・ ・
What can we do for??
Isn't the accident recurring and burdening the cutting operator without taking measures to prevent the accident in a more complete state?
For this reason, we will introduce you the "Clamp Sensor" this time.
The Sensors beam at the bottom of clamp detects fingers ( or something) , then clamp stop and move up even if pedal has been footed.
Don`t you think the operator be more relief than before.
Depending on the product, there are materials which can not be cut well during cutting work, right? For example, if you cut a thick material on a plastic sheet, the cut surface may crack. Here is how to eliminate it........
「Low Speed Inverter 」！！
This is a new option that we send with full of confidence.
Combining an inverter and increased capacity motor, it is now possible to move the knife at ultra-low speed! Furthermore, in order to increase the cutting cycle, the rising speed from the bottom dead center to the upper end, is increased. It will be an option that brings a new twist to the conventional cutting concept. For details, see this video
The clamp sensor is a safety device that immediately raises the clamp gauge when four sets of sensors installed below the clamp gauge detect fingers or foreign matter other than the work. You can avoid accidents that you accidentally pinch your fingers or foreign matter placed on the work. By installing the clamp sensor, you can adjust the cutting position with peace of mind.
・When the workpieces are stacked low (Less)
When the clamp operation is in a wide range, the upper and lower sensors work together to detect foreign matter.
・When the workpieces are piled up (Many)
In a narrow clamp range, only the upper sensor works and detects foreign matter.
It is now possible to avoid a clamp accident at the time of the day, which was difficult to prevent by any means, without touching the clamp. In the case of conventional soft clamps, even though the clamps are soft, the clamps were supposed to pinch a finger or the like, so even if the degree of injury decreased, the operator met with pain. On the other hand, by introducing a clamp sensor, the clamp rises before it hits the finger, so the finger is not even scratched. In addition, even if the work has waviness, curls, swelling of saddle stitch, etc., it can be handled by setting the sensitivity adjustment on the panel. Furthermore, it is possible to set the clamp operating speed in case of register in two steps on the panel.
■The clamp sensor operates within a range of 80 mm if the object is 5 mm or more and 1.5 mm or more behind the clamp edge. In addition, things that allow objects to pass through may not work. For details, see the instruction manual.
■The operation may be delayed depending on the clamp throw setting. For details, see the instruction manual.
■If the knife ring is removed when the knife is replaced, the sensor is blocked by the back gauge, or the sensor setting is turned off, it will not work.
■ The clamp sensor is a safety device. Do not overreliance on this function, and be sure that the operator pays sufficient attention to safety and works responsibly.
